Gemmy Airblown Inflatable Set-up

The 4 foot Airblown Inflatables are generally designed for indoor or covered patio use. Not because the high quality is any different, because it is not, but rather the A/C adaptor plug used for the 4 foot is only UL rated for indoor use.

To setup any Airblown Inflatable 4 foot follow these general instructions

1. Remove contents from packaging.
2. Plug adapter into connection on the back of Airblown. (As shown in Figure below)
3. Zip zipper at base of fan. Airblown will then fully inflate (As shown in Figure below)
4. Plug adapter plug into standard wall outlet.(As shown in Figure below)
5. Fan will immediately begin to start the flow of air.
6. Your Airblown is weighted at the base with a sealed weight-bag which allows you to adjust to a certain position to maintain balance.
7. To deflate, unplug adapter. For faster deflation, unzip zipper after unplugging adapter. Do not unplug by pulling on cord.


For all the 6 foot Character Airblown Inflatables and up the setup is pretty much the same, and all are designed for outdoor use, but not recommended to use during harse weather conditions.
The contents in each box includes the Airblown Inflatable Character, 4 pieces of nylon tethers, 4 metal stakes, C-7 Light bulb (spare included), and 5 amp fuse (spare included).

To setup any Character Inflatable 6 feet and over follow these general instructions:
1. Remove contents from packaging. Lay out deflated Airblown Inflatable in a clear area.
2. Locate four metal clips on the bottom of the fabric and attach to the plastic legs. (As shown in Figure below)
3. Turn unit upright. Make sure the air intake is clear of fabric or other obstruction and zipper is fully closed.
4. Plug into receptacle or other outlet device to inflate your Airblown Inflatable. (As shown in Figure below)
5. Once fully inflated, clip the tethers to each of the ring grommets on the side of the Airblown Inflatable.
6. Insert the stakes into the ground and attach the tethers. (As shown in Figure below)
7. To deflate, unplug fan. For faster deflation, unzip zipper after unplugging fan. Do not unplug by pulling on cord.


In the event the light bulb burns out inside follow these instructions for lamp replacement:

1. Grasp plug and remove from receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open the zipper on back of Airblown Inflatable and locate the blown out lamp.
3. Open the protective lamp cover carefully by pressing down the two locking side tabs simultaneously.
4. Replace with the same type of lamp: 7W maximum, candelabra base, UL classified C-7 lamp (one-piece replacement lamp provided).
5. Do not over-tighten the lamp as this may damage the lamp or lamp-holder.

In the event the fuse burns out follow these instructions to replace the fuse:

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide-open the fuse-access cover on top of the attachment plug towards blades.
3. Remove fuse carefully.
4. Risk of Fire: Replace fuse only with 5Amp, 125V fuse (provided with product).
5. Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.
6. Risk of Fire: Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if attachment plug is damaged.

If your Airblown Inflatable is not inflating, the problem may be:
1. The power source is disabled or the cord may be unplugged.
2. The fuse may be blown.
3. Debris may be lodged in the motor.
4. The zipper may not be securely fastened, sealing the Airblown Inflatable.
5. The temperature may be below 14 F (-10 C).